Ambito dei contenuti

CN-MET

Il contenuto di questa pagina è attualmente disponibile solo in inglese.
Inizio del progetto 19.12.2005
Fine del progetto 31.12.2009
Temi Ricerca e collaborazioni
Sistemi di rilevamento e previsione
Regione Svizzera
Stato Progetti conclusi

Introduction

Main purpose of the CN-MET project (Centrale Nucléaire et METéorologie) is to bring up to date the system delivering weather information necessary to the population safety in case of a nuclear hazard. CN-MET represents the coupling of a specifically adapted measurement network and a predictive tool in the form of a fine grid numerical weather prediction model currently developed at MeteoSwiss (COSMO-2). This new tool, calling upon modern measurement and modeling techniques of the atmosphere, represents a solution which will keep all its relevance for the next decades.

In case of a nuclear accident, the necessary atmospheric data used to calculate the diffusion of a contaminated air mass will be provided by a fine grid numerical model, covering the whole Swiss territory. The new measurement network within CN-MET is directly adapted to provide the best information (initial and boundary conditions, and test measurements) for this model. CN-MET not only ensures the emergency preparedness for the concerned population on a local scale, but also enhances it on a regional scale corresponding to the Swiss Plateau.

The measurement network

With the CN-MET project a new measurement network (Figure 1) is being set up which includes:

  • three remote sensing sites measuring wind and temperature profiles within the planetary boundary layer (PBL), located downwind, upwind and in the center of the domain (data examples cf. Figures 2 and 3),
  • surface weather stations from the new SwissMetNet (SMN) network (with additional turbulence measurements) at each of the four nuclear power plants,
  • four SMN boundary layer stations in order to add information on wind and temperature measurement in the PBL, which are integrated in the MeteoSwiss measurement network.
Figure 1: The CN-MET measurement network, including 3 remote sensing sites (green), 4 SMN stations at the nuclear power plants (blue) and 4 SMN Surface Layer stations (red).
Figure 1: The CN-MET measurement network, including 3 remote sensing sites (green), 4 SMN stations at the nuclear power plants (blue) and 4 SMN Surface Layer stations (red).
Figure 2: Top: Vertical temperature profiles measured on 18 March 2006 (time step of ca. 90 sec) with a microwave radiometer installed at the Aerological Station in Payerne. Bottom: Comparison with the sounding in Payerne at 00, 12 and 24 UTC; red: sounding, blue: radiometer.
Figure 2: Top: Vertical temperature profiles measured on 18 March 2006 (time step of ca. 90 sec) with a microwave radiometer installed at the Aerological Station in Payerne. Bottom: Comparison with the sounding in Payerne at 00, 12 and 24 UTC; red: sounding, blue: radiometer.

The fine-grid model COSMO-2

As a part of the CN-MET project, a new fine-grid numerical weather prediction model (Figure 4), COSMO-2, is being developed, with the following caracteristics:

  • data assimilation from the above mentioned network for initial conditions, thus offering a complete and coherent image of the state of the atmosphere and its evolution (wind, turbulence, precipitation, etc)
  • providing input data for the dispersion models in operation at the Swiss Federal Nuclear Safety Inspectorate (ENSI; Eidgenössisches Nuklearsicherheitsinspektorat) for short-distance dispersion calculation around the Swiss nuclear power plants
  • providing an 24 hours forecast every 3 hours, with a 10 minutes output time step, for the whole Swiss Plateau
  • providing an emergency mode, activated on demand by the ENSI, with an hourly computation of a short-range forecast, in order to satisfy the high requirements of a predictive emergency response tool.
Figure 4: Example of a simulated wind field on the Swiss Plateau obtained by the new fine grid model COSMO-2 with a horizontal resolution of 2.2 km. Background colour shading according to terrain height in the model.
Figure 4: Example of a simulated wind field on the Swiss Plateau obtained by the new fine grid model COSMO-2 with a horizontal resolution of 2.2 km. Background colour shading according to terrain height in the model.

Contacts

  • Bertrand Calpini, CN-MET project leader, MeteoSwiss, Aerological Station, P.O. BOX 316, CH-1530 Payerne, Switzerland
  • Dominique Ruffieux, responsible for the CN-MET measurement network, MeteoSwiss, Aerological Station, P.O. BOX 316, CH-1530 Payerne, Switzerland
  • Philippe Steiner, responsible for the development of COSMO-2, MeteoSwiss, P.O. BOX 257, CH-8058 Zürich, Switzerland
  • Olaf Maier, project management, MeteoSwiss, Aerological Station, P.O. BOX 316, CH-1530 Payerne, Switzerland
  • Pirmin Kaufmann, CN-MET operating manager, MeteoSwiss, P.O. BOX 257, CH-8058 Zürich, Switzerland

 

Links

COSMO-Prognosesysteme

Das Wettervorhersagesystem der MeteoSchweiz basiert auf den probabilistischen Vorhersagen der Modellkonfigurationen COSMO-1E und COSMO-2E. Beide...

Automatisches Messnetz

SwissMetNet, das automatische Messnetz von MeteoSchweiz, zählt 260 Stationen. Diese erfassen alle zehn Minuten aktuelle Daten zu Wetter und Klima.